TOSHIBA SATELLITE PRO 4300

Datos: Septiembre 21st, 2013

Para descargar los drivers para TOSHIBA SATELLITE PRO 4300 compatible con Windows, Non-OS, Windows XP, Windows ME, Windows 98, Windows 95, Windows 2000, Windows NT, Other, pulse el botón “Descargar”. Si necesita otra versión del driver o del firmware para el dispositivo, envíenos una petición. Si tiene cualquier pregunta sobre este driver, puede contactarnos mediante el formulario de contacto. En esta página también puede discutir las particularidades de la instalación, la desinstalación y la actualización de este driver.

Modelo:
4300
Fabricante:
Toshiba
Tipo de dispositivo:
Portátiles y Netbooks / Satellite Pro
Licencia:
Gratis

Windows Non-OS

Windows

Tipo: BIOS
Versión: 1.0.0.3119C
Tamaño: 686.78 Kb
Sistema operativo: Windows XP
ACPI Flash BIOS version 2.00 for Satellite Pro 4260DVD, 4280XDVD, 4280ZDVD, 4300 Series.

CHANGE HISTORY

Version 2.00  06-30-2000

  • Initial production release for Satellite Pro 4300 Series.
  • A change was made to support Super I/O.
  • Flat Panel enable control and Power Panel unit control were separated.
  • A problem was corrected where, under Windows 2000, if USB Wake-Up was set to "Enable", clicking the buttons on a USB mouse after the computer went into Standby, could result in the computer shutting down.
  • Corrected a problem that caused accessing the P-Code such as the HCI function was impossible, when operating an ACPI operating system.
  • Corrected a problem in Windows 98 that caused the mouse not to respond, if keys were pressed during the resume operation.
  • Corrected a stretched text problem.
  • Corrected a battery recognition problem when running Windows 2000.When a battery was attached to the computer when it was turned on, the battery was not recognized by the computer.
  • A problem was corrected that caused a lack of a "panel closed" sound to be generated, if the computer was powered on with the panel closed.
  • Corrected a hibernation problem in Windows 98. Cancelling hibernation under LCD mode could result in the computer switching displays to CRT mode.

Version 2.40  07-18-2000

  • A Resume/Suspend problem when running Windows, 98 or 2000, that left the screen blank, after power on, was resolved.
  • A problem was resolved that caused approximately a four minute delay in power on after using Standby or Hibernation. If the computer was set to "System Standby = 1 min." or "System Hibernation = 5 min." and then power on using the power switch, the delay could occur.

Version 2.20  06-30-2000

  • Corrected a hibernation problem in Windows 95 that caused the computer not to come out of hibernation, if battery power was low.

Version 2.10  06-30-2000

  • Power management controlling power consumption and temperature has been improved.
  • An intermittent problem causing the system to hang at the Windows 2000 screen was corrected.
  • A problem was corrected that caused a BIOS upgrade impossible, due to a particular type of FDC, if the CHGBIOSA file was used to execute the upgrade in DOS mode.
  • A problem was corrected that caused the computer to hang, after setting a password on the computer and executing suspend/resume repeatedly.

Version 2.00  06-30-2000

  • Initial production release for Satellite Pro 4300 Series.
  • A change was made to support Super I/O.
  • Flat Panel enable control and Power Panel unit control were separated.
  • A problem was corrected where, under Windows 2000, if USB Wake-Up was set to "Enable", clicking the buttons on a USB mouse after the computer went into Standby, could result in the computer shutting down.
  • Corrected a problem that caused accessing the P-Code such as the HCI function was impossible, when operating an ACPI operating system.
  • Corrected a problem in Windows 98 that caused the mouse not to respond, if keys were pressed during the resume operation.
  • Corrected a stretched text problem.
  • Corrected a battery recognition problem when running Windows 2000.When a battery was attached to the computer when it was turned on, the battery was not recognized by the computer.
  • A problem was corrected that caused a lack of a "panel closed" sound to be generated, if the computer was powered on with the panel closed.
  • Corrected a hibernation problem in Windows 98. Cancelling hibernation under LCD mode could result in the computer switching displays to CRT mode.

Version 1.80  03-24-2000

  • Corrected a failure of the PLL (Phase Locked Loop) margin within the VGA BIOS.
  • Corrected a problem using display driver version v7.30.13 when running Windows 2000. LCD mode and suspending the computer would result in a white screen.
  • A problem using TV was corrected. When the TV was turned on and after setting the computer to "Monitor auto-off. the TV screen was divided into four segments.

Version 1.70  03-23-2000

  • Corrected a problem that, when running Windows 2000, attempting to switch the Speed Step after using Rusume or Hibernation was impossible.
  • A change was made to in CHIGBIOS.exe so that pressing the F12 key, after updating the BIOS, would reset the hardware settings.
  • A change was made so that the Processor Serial Number could not be changed.
  • Corrected a problem that, when running Windows 95 and rebooting in DOS mode, it would take several minutes for the computer to go into Suspend mode.
  • Corrected a problem that when LDCM is installed, and "Dynamic CPU Frequency = Always Low", the Max Speed Value of the CPU would display an incorrect value.

Version 1.60  03-13-2000

  • Corrected an intermittent hang problem when the computer attempted to resume; if the computer had a Pentium V 450MHz processor.

Version 1.50  03-09-2000

  • Corrected a screen color issue when hot docked to a Port Replicator.
  • Corrected a problem in Windows 2000 that, when using a monitor, turning on the computer after powering off with Auto-Off, then switching to LCD, caused the LCD not to display.
  • Corrected an intermittent hang of the computer. When executing "Quality 50/Texture Swapping" in 3D Bench99, in Windows 2000 the computer might hang.

Version 1.40  02-18-2000

  • A change was made so that the Speed Step function would not change the CPU clock as a countermeasure for heat build-up.
  • Corrected a problem where, when running under a slow CPU frequency, repeating Shutdown/Suspend/Hibernation may cause the computer to hang.
  • The wait time for display control at shutdown was reduced to 2ms., in accordance with factory specifications.
  • A change was made so that the "DMA Overrun Error" would not occur when executing the FDD test in the ASP diagnostics, when "USB Legacy Mode=Enable" is set.
  • Corrected a power off issue that could be caused when running Windows NT with SP4.
  • Corrected a possible problem that, when parameter block "A" in the Flash ROM sets to "FFh", the computer would not boot.
  • Corrected a problem that, when executing "Instant Security" under CRT mode or LCD/CRT simultaneous mode, could result in a distorted display image.
  • Corrected a problem that when setting the cooling method when running Windows 95/98, the settings would not be accurate.

Version 1.20  01-02-2000

  • Initial production BIOS for these models.
Tipo: BIOS
Versión: 2.1.0.1
Tamaño: 688.07 Kb
Sistema operativo: Windows XP
ACPI Flash BIOS version 2.10 for Satellite Pro 4260DVD, 4280XDVD, 4280ZDVD, 4300 Series.

CHANGE HISTORY

Version 2.10  06-30-2000

  • Power management controlling power consumption and temperature has been improved.
  • An intermittent problem causing the system to hang at the Windows 2000 screen was corrected.
  • A problem was corrected that caused a BIOS upgrade impossible, due to a particular type of FDC, if the CHGBIOSA file was used to execute the upgrade in DOS mode.
  • A problem was corrected that caused the computer to hang, after setting a password on the computer and executing suspend/resume repeatedly.

Version 2.40  07-18-2000

  • A Resume/Suspend problem when running Windows, 98 or 2000, that left the screen blank, after power on, was resolved.
  • A problem was resolved that caused approximately a four minute delay in power on after using Standby or Hibernation. If the computer was set to "System Standby = 1 min." or "System Hibernation = 5 min." and then power on using the power switch, the delay could occur.

Version 2.20  06-30-2000

  • Corrected a hibernation problem in Windows 95 that caused the computer not to come out of hibernation, if battery power was low.

Version 2.10  06-30-2000

  • Power management controlling power consumption and temperature has been improved.
  • An intermittent problem causing the system to hang at the Windows 2000 screen was corrected.
  • A problem was corrected that caused a BIOS upgrade impossible, due to a particular type of FDC, if the CHGBIOSA file was used to execute the upgrade in DOS mode.
  • A problem was corrected that caused the computer to hang, after setting a password on the computer and executing suspend/resume repeatedly.

Version 2.00  06-30-2000

  • Initial production release for Satellite Pro 4300 Series.
  • A change was made to support Super I/O.
  • Flat Panel enable control and Power Panel unit control were separated.
  • A problem was corrected where, under Windows 2000, if USB Wake-Up was set to "Enable", clicking the buttons on a USB mouse after the computer went into Standby, could result in the computer shutting down.
  • Corrected a problem that caused accessing the P-Code such as the HCI function was impossible, when operating an ACPI operating system.
  • Corrected a problem in Windows 98 that caused the mouse not to respond, if keys were pressed during the resume operation.
  • Corrected a stretched text problem.
  • Corrected a battery recognition problem when running Windows 2000.When a battery was attached to the computer when it was turned on, the battery was not recognized by the computer.
  • A problem was corrected that caused a lack of a "panel closed" sound to be generated, if the computer was powered on with the panel closed.
  • Corrected a hibernation problem in Windows 98. Cancelling hibernation under LCD mode could result in the computer switching displays to CRT mode.

Version 1.80  03-24-2000

  • Corrected a failure of the PLL (Phase Locked Loop) margin within the VGA BIOS.
  • Corrected a problem using display driver version v7.30.13 when running Windows 2000. LCD mode and suspending the computer would result in a white screen.
  • A problem using TV was corrected. When the TV was turned on and after setting the computer to "Monitor auto-off. the TV screen was divided into four segments.

Version 1.70  03-23-2000

  • Corrected a problem that, when running Windows 2000, attempting to switch the Speed Step after using Rusume or Hibernation was impossible.
  • A change was made to in CHIGBIOS.exe so that pressing the F12 key, after updating the BIOS, would reset the hardware settings.
  • A change was made so that the Processor Serial Number could not be changed.
  • Corrected a problem that, when running Windows 95 and rebooting in DOS mode, it would take several minutes for the computer to go into Suspend mode.
  • Corrected a problem that when LDCM is installed, and "Dynamic CPU Frequency = Always Low", the Max Speed Value of the CPU would display an incorrect value.

Version 1.60  03-13-2000

  • Corrected an intermittent hang problem when the computer attempted to resume; if the computer had a Pentium V 450MHz processor.

Version 1.50  03-09-2000

  • Corrected a screen color issue when hot docked to a Port Replicator.
  • Corrected a problem in Windows 2000 that, when using a monitor, turning on the computer after powering off with Auto-Off, then switching to LCD, caused the LCD not to display.
  • Corrected an intermittent hang of the computer. When executing "Quality 50/Texture Swapping" in 3D Bench99, in Windows 2000 the computer might hang.

Version 1.40  02-18-2000

  • A change was made so that the Speed Step function would not change the CPU clock as a countermeasure for heat build-up.
  • Corrected a problem where, when running under a slow CPU frequency, repeating Shutdown/Suspend/Hibernation may cause the computer to hang.
  • The wait time for display control at shutdown was reduced to 2ms., in accordance with factory specifications.
  • A change was made so that the "DMA Overrun Error" would not occur when executing the FDD test in the ASP diagnostics, when "USB Legacy Mode=Enable" is set.
  • Corrected a power off issue that could be caused when running Windows NT with SP4.
  • Corrected a possible problem that, when parameter block "A" in the Flash ROM sets to "FFh", the computer would not boot.
  • Corrected a problem that, when executing "Instant Security" under CRT mode or LCD/CRT simultaneous mode, could result in a distorted display image.
  • Corrected a problem that when setting the cooling method when running Windows 95/98, the settings would not be accurate.

Version 1.20  01-02-2000

  • Initial production BIOS for these models.
Tipo: BIOS
Versión: 1.0.0.196.0
Tamaño: 687.79 Kb
Sistema operativo: Windows XP
ACPI Flash BIOS version 2.20 for Satellite Pro 4260DVD, 4280XDVD, 4280ZDVD, 4300 Series.

CHANGE HISTORY

Version 2.20  06-30-2000

  • Corrected a hibernation problem in Windows 95 that caused the computer not to come out of hibernation, if battery power was low.

Version 2.40  07-18-2000

  • A Resume/Suspend problem when running Windows, 98 or 2000, that left the screen blank, after power on, was resolved.
  • A problem was resolved that caused approximately a four minute delay in power on after using Standby or Hibernation. If the computer was set to "System Standby = 1 min." or "System Hibernation = 5 min." and then power on using the power switch, the delay could occur.

Version 2.20  06-30-2000

  • Corrected a hibernation problem in Windows 95 that caused the computer not to come out of hibernation, if battery power was low.

Version 2.10  06-30-2000

  • Power management controlling power consumption and temperature has been improved.
  • An intermittent problem causing the system to hang at the Windows 2000 screen was corrected.
  • A problem was corrected that caused a BIOS upgrade impossible, due to a particular type of FDC, if the CHGBIOSA file was used to execute the upgrade in DOS mode.
  • A problem was corrected that caused the computer to hang, after setting a password on the computer and executing suspend/resume repeatedly.

Version 2.00  06-30-2000

  • Initial production release for Satellite Pro 4300 Series.
  • A change was made to support Super I/O.
  • Flat Panel enable control and Power Panel unit control were separated.
  • A problem was corrected where, under Windows 2000, if USB Wake-Up was set to "Enable", clicking the buttons on a USB mouse after the computer went into Standby, could result in the computer shutting down.
  • Corrected a problem that caused accessing the P-Code such as the HCI function was impossible, when operating an ACPI operating system.
  • Corrected a problem in Windows 98 that caused the mouse not to respond, if keys were pressed during the resume operation.
  • Corrected a stretched text problem.
  • Corrected a battery recognition problem when running Windows 2000.When a battery was attached to the computer when it was turned on, the battery was not recognized by the computer.
  • A problem was corrected that caused a lack of a "panel closed" sound to be generated, if the computer was powered on with the panel closed.
  • Corrected a hibernation problem in Windows 98. Cancelling hibernation under LCD mode could result in the computer switching displays to CRT mode.

Version 1.80  03-24-2000

  • Corrected a failure of the PLL (Phase Locked Loop) margin within the VGA BIOS.
  • Corrected a problem using display driver version v7.30.13 when running Windows 2000. LCD mode and suspending the computer would result in a white screen.
  • A problem using TV was corrected. When the TV was turned on and after setting the computer to "Monitor auto-off. the TV screen was divided into four segments.

Version 1.70  03-23-2000

  • Corrected a problem that, when running Windows 2000, attempting to switch the Speed Step after using Rusume or Hibernation was impossible.
  • A change was made to in CHIGBIOS.exe so that pressing the F12 key, after updating the BIOS, would reset the hardware settings.
  • A change was made so that the Processor Serial Number could not be changed.
  • Corrected a problem that, when running Windows 95 and rebooting in DOS mode, it would take several minutes for the computer to go into Suspend mode.
  • Corrected a problem that when LDCM is installed, and "Dynamic CPU Frequency = Always Low", the Max Speed Value of the CPU would display an incorrect value.

Version 1.60  03-13-2000

  • Corrected an intermittent hang problem when the computer attempted to resume; if the computer had a Pentium V 450MHz processor.

Version 1.50  03-09-2000

  • Corrected a screen color issue when hot docked to a Port Replicator.
  • Corrected a problem in Windows 2000 that, when using a monitor, turning on the computer after powering off with Auto-Off, then switching to LCD, caused the LCD not to display.
  • Corrected an intermittent hang of the computer. When executing "Quality 50/Texture Swapping" in 3D Bench99, in Windows 2000 the computer might hang.

Version 1.40  02-18-2000

  • A change was made so that the Speed Step function would not change the CPU clock as a countermeasure for heat build-up.
  • Corrected a problem where, when running under a slow CPU frequency, repeating Shutdown/Suspend/Hibernation may cause the computer to hang.
  • The wait time for display control at shutdown was reduced to 2ms., in accordance with factory specifications.
  • A change was made so that the "DMA Overrun Error" would not occur when executing the FDD test in the ASP diagnostics, when "USB Legacy Mode=Enable" is set.
  • Corrected a power off issue that could be caused when running Windows NT with SP4.
  • Corrected a possible problem that, when parameter block "A" in the Flash ROM sets to "FFh", the computer would not boot.
  • Corrected a problem that, when executing "Instant Security" under CRT mode or LCD/CRT simultaneous mode, could result in a distorted display image.
  • Corrected a problem that when setting the cooling method when running Windows 95/98, the settings would not be accurate.

Version 1.20  01-02-2000

  • Initial production BIOS for these models.
Tipo: BIOS
Versión: 3.1.1
Tamaño: 689.3 Kb
Sistema operativo: Windows XP
ACPI Flash BIOS version 2.40 for Satellite Pro 4260DVD, 4280XDVD, 4280ZDVD, 4300 Series.

CHANGE HISTORY

Version 2.40  07-18-2000

  • A Resume/Suspend problem when running Windows, 98 or 2000, that left the screen blank, after power on, was resolved.
  • A problem was resolved that caused approximately a four minute delay in power on after using Standby or Hibernation. If the computer was set to "System Standby = 1 min." or "System Hibernation = 5 min." and then power on using the power switch, the delay could occur.

Version 2.20  06-30-2000

  • Corrected a hibernation problem in Windows 95 that caused the computer not to come out of hibernation, if battery power was low.

Version 2.10  06-30-2000

  • Power management controlling power consumption and temperature has been improved.
  • An intermittent problem causing the system to hang at the Windows 2000 screen was corrected.
  • A problem was corrected that caused a BIOS upgrade impossible, due to a particular type of FDC, if the CHGBIOSA file was used to execute the upgrade in DOS mode.
  • A problem was corrected that caused the computer to hang, after setting a password on the computer and executing suspend/resume repeatedly.

Version 2.00  06-30-2000

  • Initial production release for Satellite Pro 4300 Series.
  • A change was made to support Super I/O.
  • Flat Panel enable control and Power Panel unit control were separated.
  • A problem was corrected where, under Windows 2000, if USB Wake-Up was set to "Enable", clicking the buttons on a USB mouse after the computer went into Standby, could result in the computer shutting down.
  • Corrected a problem that caused accessing the P-Code such as the HCI function was impossible, when operating an ACPI operating system.
  • Corrected a problem in Windows 98 that caused the mouse not to respond, if keys were pressed during the resume operation.
  • Corrected a stretched text problem.
  • Corrected a battery recognition problem when running Windows 2000.When a battery was attached to the computer when it was turned on, the battery was not recognized by the computer.
  • A problem was corrected that caused a lack of a "panel closed" sound to be generated, if the computer was powered on with the panel closed.
  • Corrected a hibernation problem in Windows 98. Cancelling hibernation under LCD mode could result in the computer switching displays to CRT mode.

Version 1.80  03-24-2000

  • Corrected a failure of the PLL (Phase Locked Loop) margin within the VGA BIOS.
  • Corrected a problem using display driver version v7.30.13 when running Windows 2000. LCD mode and suspending the computer would result in a white screen.
  • A problem using TV was corrected. When the TV was turned on and after setting the computer to "Monitor auto-off. the TV screen was divided into four segments.

Version 1.70  03-23-2000

  • Corrected a problem that, when running Windows 2000, attempting to switch the Speed Step after using Rusume or Hibernation was impossible.
  • A change was made to in CHIGBIOS.exe so that pressing the F12 key, after updating the BIOS, would reset the hardware settings.
  • A change was made so that the Processor Serial Number could not be changed.
  • Corrected a problem that, when running Windows 95 and rebooting in DOS mode, it would take several minutes for the computer to go into Suspend mode.
  • Corrected a problem that when LDCM is installed, and "Dynamic CPU Frequency = Always Low", the Max Speed Value of the CPU would display an incorrect value.

Version 1.60  03-13-2000

  • Corrected an intermittent hang problem when the computer attempted to resume; if the computer had a Pentium V 450MHz processor.

Version 1.50  03-09-2000

  • Corrected a screen color issue when hot docked to a Port Replicator.
  • Corrected a problem in Windows 2000 that, when using a monitor, turning on the computer after powering off with Auto-Off, then switching to LCD, caused the LCD not to display.
  • Corrected an intermittent hang of the computer. When executing "Quality 50/Texture Swapping" in 3D Bench99, in Windows 2000 the computer might hang.

Version 1.40  02-18-2000

  • A change was made so that the Speed Step function would not change the CPU clock as a countermeasure for heat build-up.
  • Corrected a problem where, when running under a slow CPU frequency, repeating Shutdown/Suspend/Hibernation may cause the computer to hang.
  • The wait time for display control at shutdown was reduced to 2ms., in accordance with factory specifications.
  • A change was made so that the "DMA Overrun Error" would not occur when executing the FDD test in the ASP diagnostics, when "USB Legacy Mode=Enable" is set.
  • Corrected a power off issue that could be caused when running Windows NT with SP4.
  • Corrected a possible problem that, when parameter block "A" in the Flash ROM sets to "FFh", the computer would not boot.
  • Corrected a problem that, when executing "Instant Security" under CRT mode or LCD/CRT simultaneous mode, could result in a distorted display image.
  • Corrected a problem that when setting the cooling method when running Windows 95/98, the settings would not be accurate.

Version 1.20  01-02-2000

  • Initial production BIOS for these models.
Tipo: BIOS
Versión: 2.2.97
Tamaño: 688.98 Kb
Sistema operativo: Windows XP
ACPI Flash BIOS version 2.50 for Satellite Pro 4260DVD, 4280XDVD, 4280ZDVD, 4300 Series.

CHANGE HISTORY

Version 2.50  08-02-2000

  • Corrected a problem where the computer would not see the FDD when running under Windows 95, causing the computer to hang. This problem would only occur on computers manufactured with a PCB containing the Super I/O chip.

Version 2.40  07-18-2000

  • A Resume/Suspend problem when running Windows, 98 or 2000, that left the screen blank, after power on, was resolved.
  • A problem was resolved that caused approximately a four minute delay in power on after using Standby or Hibernation. If the computer was set to "System Standby = 1 min." or "System Hibernation = 5 min." and then power on using the power switch, the delay could occur.

Version 2.20  06-30-2000

  • Corrected a hibernation problem in Windows 95 that caused the computer not to come out of hibernation, if battery power was low.

Version 2.10  06-30-2000

  • Power management controlling power consumption and temperature has been improved.
  • An intermittent problem causing the system to hang at the Windows 2000 screen was corrected.
  • A problem was corrected that caused a BIOS upgrade impossible, due to a particular type of FDC, if the CHGBIOSA file was used to execute the upgrade in DOS mode.
  • A problem was corrected that caused the computer to hang, after setting a password on the computer and executing suspend/resume repeatedly.

Version 2.00  06-30-2000

  • Initial production release for Satellite Pro 4300 Series.
  • A change was made to support Super I/O.
  • Flat Panel enable control and Power Panel unit control were separated.
  • A problem was corrected where, under Windows 2000, if USB Wake-Up was set to "Enable", clicking the buttons on a USB mouse after the computer went into Standby, could result in the computer shutting down.
  • Corrected a problem that caused accessing the P-Code such as the HCI function was impossible, when operating an ACPI operating system.
  • Corrected a problem in Windows 98 that caused the mouse not to respond, if keys were pressed during the resume operation.
  • Corrected a stretched text problem.
  • Corrected a battery recognition problem when running Windows 2000.When a battery was attached to the computer when it was turned on, the battery was not recognized by the computer.
  • A problem was corrected that caused a lack of a "panel closed" sound to be generated, if the computer was powered on with the panel closed.
  • Corrected a hibernation problem in Windows 98. Cancelling hibernation under LCD mode could result in the computer switching displays to CRT mode.

Version 1.80  03-24-2000

  • Corrected a failure of the PLL (Phase Locked Loop) margin within the VGA BIOS.
  • Corrected a problem using display driver version v7.30.13 when running Windows 2000. LCD mode and suspending the computer would result in a white screen.
  • A problem using TV was corrected. When the TV was turned on and after setting the computer to "Monitor auto-off. the TV screen was divided into four segments.

Version 1.70  03-23-2000

  • Corrected a problem that, when running Windows 2000, attempting to switch the Speed Step after using Rusume or Hibernation was impossible.
  • A change was made to in CHIGBIOS.exe so that pressing the F12 key, after updating the BIOS, would reset the hardware settings.
  • A change was made so that the Processor Serial Number could not be changed.
  • Corrected a problem that, when running Windows 95 and rebooting in DOS mode, it would take several minutes for the computer to go into Suspend mode.
  • Corrected a problem that when LDCM is installed, and "Dynamic CPU Frequency = Always Low", the Max Speed Value of the CPU would display an incorrect value.

Version 1.60  03-13-2000

  • Corrected an intermittent hang problem when the computer attempted to resume; if the computer had a Pentium V 450MHz processor.

Version 1.50  03-09-2000

  • Corrected a screen color issue when hot docked to a Port Replicator.
  • Corrected a problem in Windows 2000 that, when using a monitor, turning on the computer after powering off with Auto-Off, then switching to LCD, caused the LCD not to display.
  • Corrected an intermittent hang of the computer. When executing "Quality 50/Texture Swapping" in 3D Bench99, in Windows 2000 the computer might hang.

Version 1.40  02-18-2000

  • A change was made so that the Speed Step function would not change the CPU clock as a countermeasure for heat build-up.
  • Corrected a problem where, when running under a slow CPU frequency, repeating Shutdown/Suspend/Hibernation may cause the computer to hang.
  • The wait time for display control at shutdown was reduced to 2ms., in accordance with factory specifications.
  • A change was made so that the "DMA Overrun Error" would not occur when executing the FDD test in the ASP diagnostics, when "USB Legacy Mode=Enable" is set.
  • Corrected a power off issue that could be caused when running Windows NT with SP4.
  • Corrected a possible problem that, when parameter block "A" in the Flash ROM sets to "FFh", the computer would not boot.
  • Corrected a problem that, when executing "Instant Security" under CRT mode or LCD/CRT simultaneous mode, could result in a distorted display image.
  • Corrected a problem that when setting the cooling method when running Windows 95/98, the settings would not be accurate.

Version 1.20  01-02-2000

  • Initial production BIOS for these models.
Tipo: BIOS
Versión: 1.1.0.0b
Tamaño: 689.42 Kb
Sistema operativo: Windows XP
ACPI Flash BIOS version 2.60 for Satellite Pro 4260DVD, 4280XDVD, 4280ZDVD, 4300 Series.

CHANGE HISTORY

Version 2.60  07-27-2000

  • Corrected an infrequent problem that slowed the speed of a system reboot, when the reset switch was used.
  • Corrected a problem when running Windows ME, that would cause the system to hang when suspending/resuming the computer after switching Step Speed.
  • Fixed an issue that caused one line on the right side of the display to not be seen, when the CRT setting was 1600x1200 at 75Hz.

Version 2.50  08-02-2000

  • Corrected a problem where the computer would not see the FDD when running under Windows 95, causing the computer to hang. This problem would only occur on computers manufactured with a PCB containing the Super I/O chip.

Version 2.40  07-18-2000

  • A Resume/Suspend problem when running Windows, 98 or 2000, that left the screen blank, after power on, was resolved.
  • A problem was resolved that caused approximately a four minute delay in power on after using Standby or Hibernation. If the computer was set to "System Standby = 1 min." or "System Hibernation = 5 min." and then power on using the power switch, the delay could occur.

Version 2.20  06-30-2000

  • Corrected a hibernation problem in Windows 95 that caused the computer not to come out of hibernation, if battery power was low.

Version 2.10  06-30-2000

  • Power management controlling power consumption and temperature has been improved.
  • An intermittent problem causing the system to hang at the Windows 2000 screen was corrected.
  • A problem was corrected that caused a BIOS upgrade impossible, due to a particular type of FDC, if the CHGBIOSA file was used to execute the upgrade in DOS mode.
  • A problem was corrected that caused the computer to hang, after setting a password on the computer and executing suspend/resume repeatedly.

Version 2.00  06-30-2000

  • Initial production release for Satellite Pro 4300 Series.
  • A change was made to support Super I/O.
  • Flat Panel enable control and Power Panel unit control were separated.
  • A problem was corrected where, under Windows 2000, if USB Wake-Up was set to "Enable", clicking the buttons on a USB mouse after the computer went into Standby, could result in the computer shutting down.
  • Corrected a problem that caused accessing the P-Code such as the HCI function was impossible, when operating an ACPI operating system.
  • Corrected a problem in Windows 98 that caused the mouse not to respond, if keys were pressed during the resume operation.
  • Corrected a stretched text problem.
  • Corrected a battery recognition problem when running Windows 2000.When a battery was attached to the computer when it was turned on, the battery was not recognized by the computer.
  • A problem was corrected that caused a lack of a "panel closed" sound to be generated, if the computer was powered on with the panel closed.
  • Corrected a hibernation problem in Windows 98. Cancelling hibernation under LCD mode could result in the computer switching displays to CRT mode.

Version 1.80  03-24-2000

  • Corrected a failure of the PLL (Phase Locked Loop) margin within the VGA BIOS.
  • Corrected a problem using display driver version v7.30.13 when running Windows 2000. LCD mode and suspending the computer would result in a white screen.
  • A problem using TV was corrected. When the TV was turned on and after setting the computer to "Monitor auto-off. the TV screen was divided into four segments.

Version 1.70  03-23-2000

  • Corrected a problem that, when running Windows 2000, attempting to switch the Speed Step after using Rusume or Hibernation was impossible.
  • A change was made to in CHIGBIOS.exe so that pressing the F12 key, after updating the BIOS, would reset the hardware settings.
  • A change was made so that the Processor Serial Number could not be changed.
  • Corrected a problem that, when running Windows 95 and rebooting in DOS mode, it would take several minutes for the computer to go into Suspend mode.
  • Corrected a problem that when LDCM is installed, and "Dynamic CPU Frequency = Always Low", the Max Speed Value of the CPU would display an incorrect value.

Version 1.60  03-13-2000

  • Corrected an intermittent hang problem when the computer attempted to resume; if the computer had a Pentium V 450MHz processor.

Version 1.50  03-09-2000

  • Corrected a screen color issue when hot docked to a Port Replicator.
  • Corrected a problem in Windows 2000 that, when using a monitor, turning on the computer after powering off with Auto-Off, then switching to LCD, caused the LCD not to display.
  • Corrected an intermittent hang of the computer. When executing "Quality 50/Texture Swapping" in 3D Bench99, in Windows 2000 the computer might hang.

Version 1.40  02-18-2000

  • A change was made so that the Speed Step function would not change the CPU clock as a countermeasure for heat build-up.
  • Corrected a problem where, when running under a slow CPU frequency, repeating Shutdown/Suspend/Hibernation may cause the computer to hang.
  • The wait time for display control at shutdown was reduced to 2ms., in accordance with factory specifications.
  • A change was made so that the "DMA Overrun Error" would not occur when executing the FDD test in the ASP diagnostics, when "USB Legacy Mode=Enable" is set.
  • Corrected a power off issue that could be caused when running Windows NT with SP4.
  • Corrected a possible problem that, when parameter block "A" in the Flash ROM sets to "FFh", the computer would not boot.
  • Corrected a problem that, when executing "Instant Security" under CRT mode or LCD/CRT simultaneous mode, could result in a distorted display image.
  • Corrected a problem that when setting the cooling method when running Windows 95/98, the settings would not be accurate.

Version 1.20  01-02-2000

  • Initial production BIOS for these models.
Tipo: BIOS
Versión: 2.3.0.8
Tamaño: 690.67 Kb
Sistema operativo: Windows XP

CHANGE HISTORY

Version 2.70 ?07-26-2001

  • A change was made to correct a problem that some PC cards with a single spec for 16 bit and 3.3VDC may malfunction.
  • Corrected a problem of no LCD display after using Suspend/Resume.

Version 2.60 ?07-27-2000

  • Corrected an infrequent problem that slowed the speed of a system reboot, when the reset switch was used.
  • Corrected a problem when running Windows ME, that would cause the system to hang when suspending/resuming the computer after switching Step Speed.
  • Fixed an issue that caused one line on the right side of the display to not be seen, when the CRT setting was 1600x1200 at 75Hz.

Version 2.50 ?08-02-2000

  • Corrected a problem where the computer would not see the FDD when running under Windows 95, causing the computer to hang. This problem would only occur on computers manufactured with a PCB containing the Super I/O chip.

Version 2.40 ?07-18-2000

  • A Resume/Suspend problem when running Windows, 98 or 2000, that left the screen blank, after power on, was resolved.
  • A problem was resolved that caused approximately a four minute delay in power on after using Standby or Hibernation. If the computer was set to "System Standby = 1 min." or "System Hibernation = 5 min." and then power on using the power switch, the delay could occur.

Version 2.20 ?06-30-2000

  • Corrected a hibernation problem in Windows 95 that caused the computer not to come out of hibernation, if battery power was low.

Version 2.10 ?06-30-2000

  • Power management controlling power consumption and temperature has been improved.
  • An intermittent problem causing the system to hang at the Windows 2000 screen was corrected.
  • A problem was corrected that caused a BIOS upgrade impossible, due to a particular type of FDC, if the CHGBIOSA file was used to execute the upgrade in DOS mode.
  • A problem was corrected that caused the computer to hang, after setting a password on the computer and executing suspend/resume repeatedly.
Tipo: Driver
Versión: 1.01
Tamaño: 1.58 Mb
Sistema operativo: Windows NT
Windows NT Advanced Power Management Subsystem version 2.05.33.
This version is updated to eliminate a CPU speed change while playing sounds.

Notes:

  1. If the previous version is installed in the system, uninstall it and reboot the PC before installing the new one.
  2. When applying the WindowsNT Service Pack, fist uninstall Toshiba Power Management (TPM), apply Service Pack, then re-install TPM. Note that TPM was certified on SP3 & SP4 & SP5 & SP6 only, so there is no assurance that it will work with future versions of Service Pack.
  3. The capability to resume PC cards after resuming depends on the HotSwap function of CardWizard and HotSwappable drivers. This capability does not work without them.
  4. Suspend request will be rejected by CardWizard when a non-HotSwappable card or ATA with open handle are in use.
  5. The system will be put into instant security mode but not actual suspend mode, when it is docked with a docking station(DS) and expansion station(EXP) and media docker(MD). This is because the option cards and SCSI in DS and EXP and MD do not support TPM. Actual suspend will cause loss of network connection and incorrect action by the SCSI device.
  6. System Auto Off does not work if Auto Run is enabled. Auto Run causes periodic interrupt, due to accessing the CD-ROM, and it prevents detection of system idle. Some unknown software may prevent System Auto Off from functioning for the same reason, even if the system appears to be idle.
  7. Ring resume function is supported with the internal modem only. It does not work with PC card modems.
Tipo: Aplicação
Versión: 1.00.00
Tamaño: 1.13 Mb
Sistema operativo: Windows NT
This is a registry patch that corrects a problem where Toshiba Utilities such as Flash Cards, Zooming, and ECO Utilities, will not work after using the Windows 7 "Restore from System Image Backup" feature.

Install Instructions

  1. Save the file to the Windows Desktop.
  2. Save all work in progress and close open applications.
  3. On the Windows Desktop, double-click the downloaded file to start the installation.
  4. Click Start at the TOSHIBA Archive Extractor window.
  5. Click Yes if a User Account Control window is displayed.
  6. The program will complete quickly.
  7. Restart the computer.
  8. Toshiba Utilities will work normally again.
Tipo: Driver
Versión: 1.63.0.11C
Tamaño: 1.05 Mb
Sistema operativo: Windows 2000
Windows 2000 Display Driver version 7.30.38-RC3 for S3 Savage MX/IX display adapter.
Tipo: Aplicação
Versión: 7.02.88-01
Tamaño: 1.44 Mb
Sistema operativo: Windows 98, Windows 95
Windows 95/98 Display Driver version 7.02.88-01 for S3 Savage MX/IX display adapter.
Tipo: Driver
Versión: 4.04
Tamaño: 71.63 Kb
Sistema operativo: Windows XP
Tipo: Driver
Versión: 7.x5.303.117
Tamaño: 1.02 Mb
Sistema operativo: Windows XP
Mobile Extensions provide Docking support (warm-dock/undock, eject password, etc.) functionality. Requires Toshiba ACPI common modules (TVALD).
Tipo: Aplicação
Versión: 3.02.02
Tamaño: 2.06 Mb
Sistema operativo: Windows XP, Windows 2000
Toshiba Utilities provide the HWSetup application and the FnEsse task switcher application. Requires Toshiba ACPI Common Modules (TVALD).
Tipo: Driver
Versión: 1.03.00_O
Tamaño: 769.65 Kb
Sistema operativo: Windows NT
Toshiba WinNT System Driver (IRQ mask for PCMCIA) version 1.3
Tipo: Aplicação
Versión: 7.13.05-01
Tamaño: 1.44 Mb
Sistema operativo: Windows 98, Windows 95
Windows 95/98 Display Driver version 7.13.05-01 for S3 Savage/MX display adapter.
Tipo: Driver
Versión: 1.00.2518
Tamaño: 1.27 Mb
Sistema operativo: Windows XP
This software is the foundation for the other Toshiba-provided utilities and power management software, and must be installed prior to installing other Toshiba software. Some Toshiba applications may refer to this as TVALD (for Toshiba Value-Added Logic Device).
Tipo: Driver
Versión: 7.7.0.348.2.x32_wCAT
Tamaño: 660.41 Kb
Sistema operativo: Windows 2000
Windows 2000 Modem Driver version MR577ALL004 for 56k V.90 Internal Modems.
Tipo: Aplicação
Versión: 2007.1.1002.2009
Tamaño: 31.5 Kb
Sistema operativo: Windows 98
This driver is for computers configured with the Realtek RTL8191SE Wireless LAN adapter.Before downloading this driver package, please verify the type of Wireless LAN adapter that is in your computer.
  • Run Device Manager.
  • Double-click Network Adapters, and verify that Realtek RTL8191SE Wireless LAN 802.11n PCI-E NIC is listed
  • .
If a Wireless LAN adapter other than the Realtek RTL8191SE is in your computer, this driver should not be downloaded.

Changes From Previous Version

  1. Fixed: The Wireless LAN card stops working and can not be detected by the system.

Installation Instructions

  1. Save this file to a convenient location such as the Windows Desktop
  2. Save all work in progress and close open applications.
  3. Double-click the downloaded file icon to start the installation.
  4. Click OK, Unzip then OK again.
  5. Click Yes if a User Account Control window is displayed.
  6. Click Next, then click Install.
  7. Click Finish.
  8. Restart the computer.

Version Verification

  1. Run Device Manager.
  2. Double-click Network Adapters, then double-click Realtek RTL8191SE Wireless LAN 802.11n PCI-E NIC.
  3. Select the Driver tab and verify that the driver version is 2007.1.1002.2009.

Tipo: Driver
Versión: 8.0.0.258.0
Tamaño: 341.88 Kb
Sistema operativo: Windows 2000
Windows 2000 FDC Driver version 1.0-RC2.
Tipo: Driver
Versión: 1.30
Tamaño: 770.4 Kb
Sistema operativo: Windows 98

Change History

  • Version 1.30 - 2009-12-11
    • Updated the Computrace function to support DDR3 memory modules.
    Version 1.20 - 2009-10-30
    • Added support for a new second source BIOS ROM.
    Version 1.10 - 2009-10-20
    • Added a workaround for a Realtek WLAN driver issue.
Tipo: Driver
Versión: 3.1.64.2
Tamaño: 4.79 Mb
Sistema operativo: Windows 2000
This driver provides important information about the HDD and SSD devices in your computer.

Changes From Previous Version

  1. When SSD/HDD Alert (V3.1.64.2) is applied to applicable Windows 7 models, the shut down speed will improve by two to three seconds.

Installation Instructions

  1. Save this file to a convenient location such as the Windows Desktop
  2. Save all work in progress and close open applications.
  3. Double-click the downloaded file icon on the Windows Desktop.
  4. Click Start.
  5. If a User Account Control (UAC) Window is displayed, click Yes.
  6. Click Yes to confirm the upgrade.
  7. Click Next to resume, and Finish to complete the installation.

Tipo: Aplicação
Versión: 2.0.
Tamaño: 43.66 Kb
Sistema operativo: Windows 98, Windows 95
Windows 95/98 Hibernation File Make Utility version 2.0.
Tipo: Driver
Versión: 1.62.0.6C
Tamaño: 590.61 Kb
Sistema operativo: Windows XP
Tipo: Driver
Versión: 1.20
Tamaño: 1.28 Mb
Sistema operativo: Windows 95

Change History

  • Version 1.20 - 2009-10-30
    • Added support for a new second source BIOS ROM.
    Version 1.10 - 2009-10-20
    • Added a workaround for a Realtek WLAN driver issue.
    Version 1.00 - 2009-09-11
    • Initial production BIOS for these models.
Tipo: Aplicação
Versión: 1.2.26
Tamaño: 272.88 Kb
Sistema operativo: Windows 2000
Toshiba Windows 2000 Mouse Sample Rate setting utility version 1.0.
Tipo: Driver
Versión: 1.45
Tamaño: 287.63 Kb
Sistema operativo: Windows 98, Windows 95
Windows 98 NDIS driver version 1.45 for MSIR (Microsoft Infrared) 3.0.
Tipo: Aplicação
Versión: 1.1.0.0b
Tamaño: 276.64 Kb
Sistema operativo: Windows 95
Windows 95 PCMCIA.INF file version 1.2.
Tipo: Driver
Versión: 4.12.01.2015
Tamaño: 7.86 Mb
Sistema operativo: Windows 98, Windows 95
Windows 95/98 Sound Driver version 4.12.01.2015 for Yamaha DS-XG sound system.
Tipo: Driver
Versión: 2.2.97
Tamaño: 5.66 Mb
Sistema operativo: Windows NT
Windows NT Sound driver version 4.00.1233 for Yamaha DS-XG sound system.
Tipo: Driver
Versión: 1.50
Tamaño: 1 Mb
Sistema operativo: Windows NT

Release Notes

  • After the update completes, the computer will automatically shut down or restart.
  • Power on the computer if it is off.
  • While the "Toshiba" LOGO is displayed, press the F2 function key to start BIOS Setup.
  • Check the version of BIOS and press the F9 function key then Enter to load setup defaults.
  • Press the F10 function key then Enter to save settings and exit. The computer will automatically reboot.

Change History

  • Version 1.50 - 2010-05-22
    • Disabled a SMART-related message during POST.
    Version 1.30 - 2009-12-11
    • Updated the Computrace function to support DDR3 memory modules.
    Version 1.20 - 2009-10-30
    • Added support for a new second source BIOS ROM.
    Version 1.10 - 2009-10-20
    • Added a workaround for a Realtek WLAN driver issue.
    Version 1.00 - 2009-09-11
    • Initial production BIOS for these models.
Tipo: Driver
Versión: 1.62.0.3C
Tamaño: 1.54 Mb
Sistema operativo: Windows XP
Tipo: Driver
Versión: 3.1.0.0
Tamaño: 289.66 Kb
Sistema operativo: Windows NT

This release adds support for unattended installation to the downloadable package when executed with the /auto switch.

Tipo: Driver
Versión: 2.01.11_O
Tamaño: 671.14 Kb
Sistema operativo: Windows 95
Windows 95 Unimodem V Drivers version 4.10.1343.01-RC5 for Tecra 8000, Portege 7000.
Tipo: Driver
Versión: 2.0USB1
Tamaño: 655 Kb
Sistema operativo: Windows 98, Windows 95, Windows 2000, Windows NT
This driver exposes system information to DMI-enabled applications.
Tipo: Aplicação
Versión: 2.1USB2-RC2.
Tamaño: 881.35 Kb
Sistema operativo: Windows 98, Windows 95, Windows 2000, Windows NT
Windows 9x, NT, 2000 TBIOS driver version 2.1USB2-RC2. TBIOS provides an interface for DMI-enabled applications to read data from the system's DMI data areas.
Tipo: Driver
Versión: 6.0.1.5904
Tamaño: 1.02 Mb
Sistema operativo: Windows 2000
This software is the foundation for the other Toshiba-provided Win2k Utilities, and must be installed first.
Tipo: Aplicação
Versión: 8.0.23
Tamaño: 1.07 Mb
Sistema operativo: Windows XP
This Utility will eliminate the "Wrong machine" messages when you try to restore the factory software image from the Config Builder CD or PIRAD CD/DVD. Click for more information about this issue.

Requires either a bootable diskette drive (FDD), or bootable CD-ROM (CD-RW, DVD-ROM/RW). If no FDD is available, requires access to CD authoring (burning) software and hardware.

Build 60303 fixes an issue where Satellite 5205-S705 units were programmed with the incorrect DMI model string.

Tipo: BIOS
Versión: 1.4.1.0
Tamaño: 1.09 Kb
Sistema operativo: Windows XP
Toshiba CMOS Setup program for portable computers.

This DOS program displays and allows you to set the CMOS/BIOS settings of your Toshiba portable computer. This program does not run in a DOS session under Windows. From Windows, you'll need to restart in MS-DOS mode in order to use this utility.

You can also access the BIOS/CMOS setup screen without having to use TSETUP by holding down the [Esc] key when you first power-on the system.

Tipo: Driver
Versión: 1.1.11.64
Tamaño: 3.6 Mb
Sistema operativo: Windows 95
Tipo: Driver
Versión: 1.62.0.6C
Tamaño: 1.35 Mb
Sistema operativo: Windows 2000
Provides Toshiba-specific Win2k display (LCD) power management functionality. Requires Toshiba ACPI common modules (TVALD).

Version 1.0.0 contained code which controlled portions of the display adapter as well as the display panel. This version (1.1.0) controls only the display panel.

Tipo: Aplicação
Versión: 1.00.04
Tamaño: 1.25 Mb
Sistema operativo: Windows 2000
This software is the foundation for the other Toshiba-provided Win2k Utilities, and must be installed first.
Tipo: Driver
Versión: 2.2.9
Tamaño: 1.35 Mb
Sistema operativo: Windows 2000
This application enables your computer to periodically search for Toshiba Software updates or alerts from Toshiba that are specific to your laptop.

Change points:

  1. Fixed: System crashes after login.
  2. Improved package downloads by using the Binary Intelligent Transfer Service (BITS).
  3. Combined the Download and Install buttons.
  4. Added a Home Link to the Settings Page.
  5. Removed the Notification Level Setting.
  6. Deletes obsolete software - i.e. Software that was already downloaded and installed.
  7. Notification message improvements.

Installation Instructions

  1. Save this file to a convenient location such as the Windows Desktop
  2. Save all work in progress and close open applications.
  3. On the Windows Desktop, double-click the downloaded file to start the installation.
  4. Answer the displayed prompts to complete the installation.

Tipo: Driver
Versión: 7.003.0522.2009
Tamaño: 1.09 Mb
Sistema operativo: Windows ME
Toshiba Hibernation Utility version 5.1
Tipo: Driver
Versión: 9.0.0.1011
Tamaño: 1.41 Mb
Sistema operativo: Windows ME
Toshiba Power Saver Utility version 4.00.00
Tipo: Driver
Versión: 1.5.08.0
Tamaño: 48.84 Kb
Sistema operativo: Windows 2000

REEL TIME

Toshiba ReelTime™ is a graphical history/indexing tool that enables you to view recently accessed files in a fun and easy-to-use format. View and scroll through your history of opened or imported files via thumbnails in an intuitive user interface. Your ReelTime display can be customized to suit your user preferences.

Toshiba ReelTime™ replaces the old fashioned “hunt-and-click” method of finding your files with an visual timeline or “reel,” Now, instead of questions like, “Where is it?” you simply ask “When did I use it?” You’ll spend less time searching, more time doing and enjoying, and keep your day in high gear. Toshiba ReelTime™ shows a row of your most recent files as graphic previews at the bottom of your display, making it easy to see at a glance what’s there. Flick through your reel to find the file you need. Then, keep it handy by dragging and docking it nearby. A brush of your finger or mouse is all it takes. ReelTime simplifies searching by automatically tracking and indexing the documents and programs you open. It groups them and presents them as visual thumbnails so you can easily find what you’re looking for.

Toshiba ReelTime™ also lets you cut through the clutter by filtering out the files you don’t want, and honing in on the ones you do. Group your photos, files and clips by type or by program to look at last month’s book reports, queue up video clips for posting, or to prep for building another great photo album. For all the things you want to do, Toshiba ReelTime™ saves you serious time.

To open TOSHIBA Reel Time:

  1. Click the Start menu.
  2. Enter "Reel" into the search field.
  3. Click "Reel Time" in the search results.
  4. The TOSHIBA Reel Time will open. By default "Everything" is selected, showing all of your files in chronological order. You can then choose to view documents, photos, videos, as well as other items. 
  5. To learn more about TOSHIBA Reel Time, click the question mark icon in the lower Right corner of the screen.

CLICK HERE for additional information about TOSHIBA Reel Time.

Tipo: Driver
Versión: 1.10
Tamaño: 4.99 Mb
Sistema operativo: Windows ME

Change History

  • Version 1.10 - 2009-10-20
    • Added a workaround for a Realtek WLAN driver issue.
    Version 1.00 - 2009-09-11
    • Initial production BIOS for these models.
Tipo: Driver
Versión: 2.00.0006
Tamaño: 1.5 Mb
Sistema operativo: Windows 2000
Windows Utilities provide the FnEsse and HWSetup applications.
Tipo: Driver
Versión: 1.1
Tamaño: 2.07 Mb
Sistema operativo: Windows 98
Toshiba Windows 98 Utilities version W984340USB3 for Satellite Pro 4260/4280.
Tipo: Driver
Versión: 2.01.11_O
Tamaño: 1.91 Mb
Sistema operativo: Windows 95
Toshiba Windows 95 Utilities version W954340USB2 for Satellite Pro 4260/4280.

Non-OS

Tipo: BIOS
Versión: 2.00
Tamaño: 686.78 Kb
Sistema operativo: Other
Tipo: BIOS
Versión: 2.10
Tamaño: 688.07 Kb
Sistema operativo: Other
Tipo: BIOS
Versión: 2.20
Tamaño: 687.79 Kb
Sistema operativo: Other
Tipo: BIOS
Versión: 2.40
Tamaño: 689.3 Kb
Sistema operativo: Other
Tipo: BIOS
Versión: 2.50
Tamaño: 688.98 Kb
Sistema operativo: Other
Tipo: BIOS
Versión: 2.70
Tamaño: 690.67 Kb
Sistema operativo: Other
Tipo: Aplicação
Versión: 1.0 build 60303
Tamaño: 1.07 Mb
Sistema operativo: Other
Tipo: BIOS
Tamaño: 1.09 Kb
Sistema operativo: Other


Más drivers

TOSHIBA SATELLITE PRO 4280ZDVD
Drivers para Portátiles y Netbooks TOSHIBA SATELLITE PRO 4280ZDVD (Other)

TOSHIBA SATELLITE PRO 4260DVD
Drivers para Portátiles y Netbooks TOSHIBA SATELLITE PRO 4260DVD (Other)

TOSHIBA SATELLITE PRO 4280XDVD
Drivers para Portátiles y Netbooks TOSHIBA SATELLITE PRO 4280XDVD (Other)

TOSHIBA SATELLITE PRO L450-EZ1522
Drivers para Portátiles y Netbooks TOSHIBA SATELLITE PRO L450-EZ1522 (Other)

TOSHIBA SATELLITE PRO L450-EZ1541
Drivers para Portátiles y Netbooks TOSHIBA SATELLITE PRO L450-EZ1541 (Other)

TOSHIBA SATELLITE PRO 410CDT
Drivers para Portátiles y Netbooks TOSHIBA SATELLITE PRO 410CDT (Other)


Solicitar driver

ejemplo